Suntec E 為重油中容量調壓型油泵浦,配高溫型軸封與預熱器安裝穴以利冷啟動,流量 170~360 L/Hr,耐油溫 130°C,相容重油、輕中油、HVO 與 B100,可選含切斷或不含切斷型式。
PRODUCT INFORMATION
Suntec E Series Oil Pumps 170~360 L/Hr | Medium Capacity Heavy Oil Preheating Pumps
- front page
- product
- Suntec Oil Pump
- heat treatment
- Suntec E Series Oil Pumps 170~360 L/Hr | Medium Capacity Heavy Oil Preheating Pumps
Product Information
- heat treatment
-
water treatment
- Deaerator
- Desulfurizer
- Arsenic remover
- Water softener (calcium and magnesium ion removal)
- Carbon filter (removes odor and residual chlorine)
- Sand filter (removal of suspended impurities)
- Iron remover (removal of iron and manganese ions)
- RO water purifier
- Pre-backwash filter
- UV ultraviolet sterilizer
- Ion exchange resin
- reverse osmosis membrane tube
- quick filter
- Various tanks for water treatment
- Various application filter media
- 美國 Clack Clark control valve
- 美國 Fleck Control Valve
- 美國 Pentair Control Valve
- 美國 Autotrol Control Valve
- Runxin Control Valve
- Injection treatment
- Technology Development Department
-
brand
- Qin Sen
- 義大利 ATLAS
- 日本 TOHKEMY
- 義大利AQUA
- US DOW
- IDEX USA
- US CLACK
- EMERSON, USA
- American PENTAIR
- SIEMENS Germany
- American PULSAFEEDER
- Denmark DANFOSS
- Thailand HAYCARB
- France SUNTEC
- UK PUROLITE
- Japanese NOP
- Japan OLYMPIA
- Japan KATSURA
- BRAHMA, Italy
- SAGINOMIYA
- HONEYWELL
- AZBIL (YAMATAKE)
- OLTREMARE
- NIPCON
- TROCHOID
- domestic
- EGO
- KATO
- LECIP
- Taiwan ATS
- JACOBI
- ETATRON
- WAVE CYBER
- BOSCHINI
- NIPPON
- WL
- CASH ACME
- YAZAKI
- RUNXIN
- About | Contact
Suitable for medium-capacity industrial burners and boilers supplying heavy and light/medium oil; the pump body has a pre-installed mounting hole for an electric heater; both single-pipe and double-pipe systems are compatible. Suntec E Series Oil Pumps 170~360 L/Hr | Medium Capacity Heavy Oil Preheating Pumps
Equipped with high-temperature shaft seal and preheater mounting cavity, oil temperature resistant up to 130°C, compatible with heavy oil and B100, mechanical interface conforms to EN 225.
中容量重油系統既要耐高溫,又要能冷啟動高黏度燃油
中容量重油燃燒設備的工作溫度高、燃油黏度大,泵的軸封若耐溫不足易滲漏,冷啟動時高黏度油又可能損壞泵與聯軸器。Suntec E 油泵浦以高溫型軸封與預熱器安裝穴,兼顧高溫耐受與冷啟動保護。
重油調壓與預熱冷啟動的運作機制
齒輪組經內建濾網吸油,送至調壓閥調節噴嘴壓力,未經噴嘴的油旁通回流。泵體設有電熱器安裝穴(加熱卡匣可左右側安裝),啟動前先通電加熱,達溫後可關閉或持續保溫;油源、管路與濾器須另行加熱。單管啟動時空氣經噴嘴旁通孔排出。1069 型無切斷、須外接電磁閥,1070 型含切斷。
Application scenarios and system pairings
E 適用中容量重油與輕中油工業燃燒器、鍋爐供油,單管與雙管皆可。更多選型見 重油燃燒機分類 and Suntec 品牌頁。前端過濾與管路加熱應另行配置。齒輪尺寸、壓力設定、切斷型式與預熱配置應依燃油黏度與工作溫度選定。請 提出產品詢問 取得型號與外接切斷閥建議。
配高溫型軸封與預熱器安裝穴、耐油溫達 130°C,相容重油與 B100,機械介面符合 EN 225產品規格
| project | content |
|---|---|
| Type | 重油中容量調壓型油泵浦,配高溫軸封與預熱器安裝穴;1070 含切斷、1069 不含切斷(須外接電磁閥) |
| 適用燃料 | 重油、輕油與中油、HVO、B100(最高 100% FAME,符合 DIN SPEC 51603-6 或 EN 14214) |
| 管路系統 | 單管或雙管 |
| Flow range | 170~360 L/Hr |
| 噴嘴壓力範圍 | 14–30 bar |
| 出廠設定壓力 | 20 bar |
| 運作黏度 | 3–75 cSt(更高黏度須灌注供油或加熱降至 75 cSt 以下) |
| 油溫(泵內) | 0–130°C |
| 進油壓力 | 輕油:吸入真空 ≤ 0.45 bar;重油:≤ 3.5 bar |
| 回油壓力 | 輕油/重油:≤ 3.5 bar |
| 額定轉速 | ≤ 3600 rpm |
| 安裝 | 法蘭,依 EN 225 |
| 進/回油口 | G 1/2 |
| 噴嘴出口 | G 1/4 |
| 壓力錶孔 | G 1/8 |
| 真空錶孔 | G 1/2 |
| 濾網 | 開孔 45 cm²;孔徑 550 µm |
| 軸徑 | Ø 11 mm(EN 225) |
| weight | 4 kg |
| 預熱器 | 卡匣 Ø 12 mm,功率 50–80 W,可左右側安裝,依 EN 50262 |
| 各齒輪型號流量對照 | [Pending confirmation from the original manufacturer's specifications] |
配高溫型軸封與預熱器安裝穴、耐油溫達 130°C,相容重油與 B100,機械介面符合 EN 225尺寸圖
| turn visual axis |
Clockwise direction |
| Number of revolutions (rpm) | 1200 ~ 3600 |
| Maximum oil temperature | 120℃ |
| Pressure(㎏/cm²) | 21-28 |
| Inlet diameter | 1/2" |
| fuel | heavy oil |
| turn visual axis |
counterclockwise |
| Number of revolutions (rpm) | 1200 ~ 3600 |
| Maximum oil temperature | 120℃ |
| Pressure(㎏/cm²) | 21-28 |
| Inlet diameter | 1/2" |
| fuel | heavy oil |
| turn visual axis |
counterclockwise |
| Number of revolutions (rpm) | 1200 ~ 3600 |
| Maximum oil temperature | 120℃ |
| Pressure(㎏/cm²) | 21-28 |
| Inlet diameter | 1/2" |
| fuel | heavy oil |